Please be aware of posted areas and drive slow! Areas to be flushed will be posted at least one day in advance. Click here for more info about hydrant flushing.
You may notice that Euclid Fire Department crews are working at fire hydrants and see water running down the street. Normally in the spring, we flush water lines through the use of fire hydrants, which is an important preventive maintenance activity. Although it may appear to waste water, this process is part of a routine maintenance program necessary to maintain the integrity of the water system and allowing us to ensure the hydrants are in proper working order. Hydrants that are found to not be in working order are tagged and submitted for repair.
As a result of the line flushing process, residents in the immediate vicinity of the work may experience temporary discoloration of their water. This discoloration consists primarily of harmless silt and air and does not affect the safety of the water. If you experience discoloration in your water after crews have been flushing in your neighborhood, clear the pipes in your home by running the cold water in all faucets for a few minutes.
The same philosophy of water line and hydrant preventive maintenance is one that you should use in your own home to ensure the quality of water inside your home. Your home’s water heater should be drained and flushed on a regular basis, according to manufacturers’ recommendations, to keep it working effectively and efficiently.
FREQUENTLY ASKED QUESTIONS
Q: Why does the water system need to be routinely flushed?
A: The city’s water distribution system is a complex network of pipes and storage reservoirs where sediment or deposits may naturally accumulate over time. If not removed, these materials may cause water quality deterioration, taste and odor problems, or discoloration of the water. Water may also stagnate in lesser used parts of the distribution system. This can result in degraded water quality.
Q: When does flushing normally occur?
A: Normally, flushing takes place for approximately a two month period during spring. In an effort to cause fewer disturbances to our customers, crews from the Fire Stations flush the lines between the hours of 8:00 AM to 4:00 PM Monday thru Friday.
Q: Is the Fire Department the only ones that flush the lines?
A: No, Fire Departments are required to flush hydrants when they are testing hydrants to make sure adequate flow and pressure is available. The Service Department may need to flush a hydrant after I repaired. Cleveland Water uses the hydrants whenever they need to perform repairs on the water lines.
Q: What should I do when I see Fire crews flushing hydrants in my area?
A: If you see a Fire crew flushing hydrants, PLEASE DRIVE CAREFULLY.
Q: What should I do after the flushing?
A: Check water by using a faucet first. If the tap water is used during or immediately after flushing, it could come out with sediment and discoloration. If you encounter discolored water, shut the water off and wait several minutes. After waiting, check the clarity by running cold water for a few minutes allowing new water to work its way into your pipes. If not, wait a few more minutes and check again. In some cases, you may experience slight discoloration for a few hours. This discoloration only affects the appearance of the water, it does not affect the taste or water quality.
Q: What should I do if my water pressure or volume seems low after flushing?
A: Check your faucet and washer screens for trapped debris.
Q: Why does the water look funny after hydrant flushing?
A: When a hydrant is opened, there will always be temporary incidences of discolored water containing fine sediment particles. There is no health hazard associated with discolored water. Allow a few hours for discoloration to dissipate. To verify the water has settled, allow your cold water tap to run a few minutes. If the discoloration persists for more than twenty-four (24) hours, please contact Cleveland Water Division at (216) 664-3060, this is a 24 hour number.
Q: Is it OK to drink sediment-laden or discolored water during temporary disturbance events?
A: It is recommended that water users wait until the water has cleared before using it for potable purposes.
Q: What is the silt in the water system after flushing?
A: Water contains minerals and these minerals react with the inside of the pipe to produce the by-product. This chemical reaction between the pipe and water is a normal and natural process. This process can occur on the inside of the pipe and prevent an adequate volume of water flow. The flushing process removes much of this by-product which is why it is done annually.
Q: What will happen if fire hydrants are turned on or off too quickly?
A: This will cause “water hammer”, which is a pressure surge or wave when water in motion is forced to stop or change direction suddenly. The pressure wave can cause major problems, from noise and vibrations to pipe collapse. In home plumbing, this is experienced as a loud bang resembling a hammering noise. Fire Department Employees have received instruction by Cleveland Water on how to operate fire hydrant valves slowly to avoid water hammer.
If you have any further questions or concerns please feel free to contact 216-289-8405.
Thank you!
Original source can be found here.
Alerts Sign-up